Laboratory Instruments

Specially designed for use in anatomy & meat cutting requirement for preparing big size specimens. The large working table and extension table opearte on ball bearing rollers.
table is made of thick stainless steel sheet with heavy axles for rigidity and firm movement.

Features:-

1. Fitted with large moving table made from stainless steel
2. Extension table operated on four ball-bearing rollers
3. Special heavy axles for easy and firm movement
4. Power consumption - 220 v
5. Fitted with premium blade, starter, cord and plug

1. Size of cutting table : 123x42cm.
2. Extension table : 61x42cm.
3. Total table travel : 120x42cm.
4. Height : 213cm.
5. Motor heavy duty : 2 h. P. Singlephase,starter
complete unit supplied with one blade,starter,cord and plug.
to work on 220/230 volts ac supply.

optional:- spare cutting blade

• The variants (models) of Laminar Air Flow Chamber are available in Stainless Steel, Electro-galvanized Steel or wood covering all applications.
• The environmental air is drawn by centri-balanced, centrifugal succession blower through pre-filters and is thrown to work plate form through high efficiency H.E.P.A. filters, retaining particulates and biological contaminants larger than 0.3 microns, Table-top is covered with stainless steel (SS-304/SS-316) sheet.
• All the compartments of the chamber are chemically sealed to prevent leakage/loss of air-pressure, Front door is collapsible type & side panels are fixed, made of crystal clear thick plexi-glass or transparent polycarbonate.
• All variants are available with U.V. Tube, Fluorescent Tube light, Gas cock & Static Pressure Manometer or Differential Pressure Magnehelic Manometer. Features:- Efficiency: 99.97% (or above) down to 0.3 micron Blower Unit: Centri-balanced, centrifugal motorized blower with ISI marked motor. 1/3 H.P. 1440RPM Discharge: Air volume 90cfm±10% Noise Level: below 65 dB Illumination by Fluorescent Tube: Light Intensity-The intensity of the light at the work Surface is in between 800 to 1000lux. Germicidal: By Ultra-Violet Tube (Approx 50 micro watts per sq.cm on the entire work surface.) Electrical: All electrical fittings are as per ISI standards. All internal wirings are protected with heat resistant material. Manometer: Available are two types:
• Dial type Magahelic Differential Pressure Manometer.
• Block Type acrylic/Plexi-glass inclined Static Pressure Manometer.

Construction:-The inner and outer chamber is made of high-grade stainless steel sheet(SS304) the strong and sturdy lid is also made of high grade stainless steel plate.(SS304) The unit is fitted with very efficient radial locking system made of stainless steel bars(SS-304), steel, chrome plated, with paddle lifting device. Supplied complete with stainless steel basket. The unit is fitted with safety valve, pressure release valve, water level indicator, cord and plug. To operate on 220/230 Volts, 50Hz AC supply.

Mode of Heating:-

Electrically heated by special flange type/immersion type heaters bearing ISI mark, to operate on 220/230 Volts, 50Hz AC supply.

Working Pressure:- The pressure inside the chamber is variable from 5psi. to 20 psi.

STANDARD CONTROLS

• Double safety radial locking arrangement.
• Brass steam release valve.
• Spring loaded safety valve of brass.
• Water level indicating gauge glass with metal guard.
• Pressure gauge.
• Electrical control box, fitted with toggle switch, indicating neon lamps and steam release valve.
• Foot Operated Paddle Lifting Device.
• Automatic pressure control switch
• Automatic low water cut off device
• Timer with alarm system
• Digital temperature indicator

· This equipment has diversified applications in various industries such as Pharma, Chemical, Food, Drugs & Beverages, F.M.C.G., Biotechnology & Microbiology and Electronics etc.

· The environmental air is drawn by centre-balanced centrifugal suction blower through pre-filter and thrown onto work platform through High Efficiency H.E.P.A. filter, retaining particulate and biological contaminants larger than 0.3 microns.

· Complete structure made of stainless steel including inters square pipes and table top.

· All the compartment of the chamber is chemically sealed to prevent leakage/loss of air pressure. Front sash (door) is counter balanced sliding up & down.

· All various are available with U.V. Tube, Fluorescent Tube Light, Gas cock & Static Pressure Manometer.

Test Facilities for the following validations are available on request:

1. Particle Count

2. D.O.P.

3. Vibration

4. .Sound

5. Light Intensity.

Size:-

· size - 90 cms x 60 cms x 60 cms (3\'x2\'x2\')

This Autoclave have Six Wing Nuts Locking of Lid with High Quality Rubber

Used for Sterilization of Surgical Instruments and Dressing Drums

Pressure Gauge with Color Coating to Display Sterilization Zones, Graduated in Kg/cm2 and lb / inch2

Equipped with Safety Pressure Release, Weight, Steam Release / Control Valve

Electric Autoclave 220 V / 50 Hz, Single Phase

Also Available in Stainless Steel Lid as Per Customer Requirement

• Air Circulating Fan.
• Digital Temperature Indicator cum controller.
• Imported Timer.
• PID Digital Temperature Controller.

• The perfect all-round solution for the histology lab
• Accuarte feed mechanism and coarse feed system in the sealed and high ergonomic desgin
• Efficient operation and maximum performance for optimum comfort
• Integrated and smooth running hand wheel, 360 degree lockable
• Integrated switch panel with multifunctional LCD display
• Clearly arranged operating controls
• All functions are controlled via touch sensitive buttons
• Section thickness setting range: 0.25-50um

Physilab senior rotary microtome
Model:SI-9 is a highly versatile sectioning device suitable for medical institutions, research & Pathological Laboratories. This microtome has special application for cutting these sections of histopathological specimens. It is ideal for those who want to avail advantages of a rotary microtome at a moderate cost. The entire mechanism stands on a heavy cast iron base ensuring stability and rigidity, its compound slide ways of critical tolerance guide the specimen block. The metal hinged cover housing protects the internal mechanism against dust and paraffin waste, it can be conveniently opened for resetting, cleaning and lubricating. The microtome is driven by a handle which can also be locked. Cutting sections are obtained in different thickness by mechanically operated crank through a lnurled in front of the instrument. The knurled knob is graduated in microns for feed setting and ready reference detent click action ensures positive adjustments in one micron increment. The knife holder unit is equipped with a rotating knife clamp to adjust desired angles for best sectioning. It as forward and backward movement to ensure contact of specimen with the knife and lateral movement to get maximum use of knife edge. Smooth & accurate specimen movement is achieved with the time proven operating principles of the feed mechanism. Travel is entirely independent to the vertical movement of the specimen block. When the feed limit reaches to an end point, it disengages itself. To bring the feed screw back, the vice is pressed slightly and the main gear wheel is turned clockwise till the screw reaches its starting position. All parts are fabricated from selected alloys and the Microtome knife is manufactured from fine grain steel tested to maintain optimum sharpness strength.

Feed Adjustment 1-25 Microns
Minimum Thickness One microns
Total Feed excursion 28mm
Object Holder(3Nos.) 1 Set
Knife 120mm in a box 1 Nos.
Honing Stone 1 Nos.
Lubricating Oil 1 Bottle
Dust Cover 1 Nos.
Operating manual 1 Nos.

Physilab plant growth chamber

• Plant Growth Chamber has outer wall made of m. S sheet duly painted and inner wall made up of heavy gauge stainless steel (304 grade)
• besides outer double walled door, a full view inner glass door allows inspection of test samples without disturbing the inner chamber conditions.
• unit is supplied with three adjustable perforated shelves.
• finned tube evaporator.
• temperature range from 5º c to 50º c ± 1º is controlled by setting microprocessor based digital temperature indicator cum controller so as to set two different temperature for day and night .
• exterior illumination with fluorescent tubes accounts for artificial day light.
• cyclic illumination conditions are regulated by automatic microprocessor based programmable timer.
• when all the tubes are on temperature from 15º c to 50º c ± 1º c can be obtained.
• CFC free eco friendly compressor.
• to work on 220/230 volts a. C.

Chamber Size in mms Cap. (Cu.Ft.) Cap. (apr.)
570x845x550 10 280 L
775x900x775 20 560 L
835x1200x825 30 840 L 900x1720x800 45.8 1282 L
1200x1200x1200 64 1792 L

It is used for determination of heat of combustion, calorific value and sulphur contents of solid and liquid fuels. The Bomb body and lid are machined from corrosion resisting stainless steel rod. It's capacity is approx. 300ml. It is provided with high pressure valve and electrodes. The calorimeter vassel and electrodes. The calorimeter vassel /stirrer FHP motor are provided and water jacket as per IP. The Bomb calorimeter is supplied with firing unit, Digital /Glass Beckman Thermometer, Pallet press, ignition Nichrome wire and pressure gauge with copper pipe fitting .

1. Bomb Calorimeter App. with digital thermometer 0.1°c read out.
2. Bomb calorimeter apparatus with digital thermometer 0.01°c readout
3. Bomb calorimeter apparatus with digital thermometer 0.01°c readout and PUFF insulated body.
4. Bomb calorimeter app. With digital thermometer 0.01°c readout with remote control.
5. Bomb calorimeter app. Digital Thermometer0.01°c readout with PUFF insulated body with remote.

Optional Accessories:

A Spare Bomb 300ml capacity.
B Spare Neoprene washer for Bomb.
C Spare Stainless Steel crucible

Transparent Anaerobic Culture Jar of 3.5 lit. capacity which is made of Polycarbonate. The lid of the jar is made of Alluminium Pressure die casting fitted with Pressure valve, Vacuum valve, Safety valve & Compound Pressure cum vacuum gauge, three finger aluminum clamp and sealing "O" ring and Air/Gas chuck

This is recommended only where inside condition of air of jar is removed thru vacuum pump and CO2 is filled in the jar thru CO2 gas cylinder to generate anaerobic conducting in the jar.

Also Supplied with Plain aluminum Pressure die casted lid which can be fitted when readymade gas packs are used to generate the anaerobic conditions inside the jar.

Supply as above and completed with following accessories

· Petri Plate Carrier, Stainless steel, for 10 petri Dishes.
· Test Tube Carrier, Stainless Steel.

It is a double walled bath with inner chamber made
of stainless steel and outer wall made of M.S sheet
duly enamel or powder coating painted. The gap
between outer and inner walls is fitted with special
grade glass wool insulation. The temperature is
controlled by a thermostat from room temperature
to 100°C with variation of ± 2%° C. The concentric
rings can be removed to accommodate containers of
various sizes.

Size Inside Chamber
1. 300x250x100mm   6 Holes of 75mm dia
2. 355x405x100mm   12 Holes of 75mm dia

Freezing microtome without co2 cylinder

This microtome is designed to the full purpose of accurate and quick diagnosis in surgery and also for the inspection of quality of rubbes and others. It has a table clamping device. The specimen rises accuracy and automatically by handle. The co2 freezing attachment is provided with a hard rubber non-conducting plate between the corrugated surface to which the object is frozen and the rest of the apparatus, which prevents the conduction of heat from the other parts of the apparatus to the specimen; thus saving time and co2. In operating this freezing attachment the valve at the bottom should first be closed and valve at the cylinder slightly opened to admit the gas into the tube. The automatic feed mechanism can be thrown out of action by turning the index finger to the extreme left or it may be set to cut sections of any desired thickness. 

Specifications :-
freezing stage : 35 mm. Dia. Total excursion of feed : 25 mm. 
feed range : 5 - 40 microns in steps of 5 microns each
weight : 13 kg. Approx. Size (in case) : 400x280x220mm. 
high pressure flexible tubing : 150 cm. (approx. )
each division of the graduated scale marks 5 microns, the microtome range being 5-40 microns. The sturdy knife holder can be tilted to a convenient angle of the knife suitable to the object. The instrument is supplied with following accessories in wooden storing cabinet. Complete with a razor 120mm with back & handle, honing stone, oil can, vinyl dust cover and operating instructions manual etc. But without co2 cylinder.

Rocking microtome (cambridge type)\

Cambridge rocking microtome is very well known and one of the best established microtomes in the world, which has given outstanding service to numerous microtomists through the years. It is designed for sectioning comparatively soft, wax-embedded tissues with a thickness range of 2 mm to 24 mm, in steps of 2mm. Calibrated in 2 micron divisions, the section cutting thickness can be set easily and quickly by a single control. It is recommended for elementary biology & pathology students. The rocking microtome is an extremely reliable instrument comprising of three moving parts. The lead screw mechanism incorporates quality precision engineering and the cutting stroke is controlled by a single control lever which minimizes the operator skill required. It carries wide choice of specimen holders cylindrical holders, standard orientating & wood block holders for sectioning wax embedded specimens. 

overall dimensions 390x200x200 mm nett weight - 4 kgs. 
size of the cabinet 450x240x260 mm gross weight - 10 kgs. 
the instrument is supplied with the following in a storing box : three standard specimen holders, razor with built in handle in a box, operating instructions and vinyl dust cover.

Revolutionary General Purpose Centrifuge Microprocessor Digital 5200 R.P.M

Microprocessor base Square M S body duly powder coated. Double walled light weight ABS lid. Fitted with microprocessor based 2 lines 16 characters LCD panel for 0-59 minutes countdown timer, digital rpm meter and programmable speed controller.

We bring forth a wide variety of Heating Mantles which are extensively used in laboratories to apply heat to containers. Our Laboratory Heating Mantle is available with a sturdy aluminum body. Its epoxy powder finish makes it a distinguished product. The Heating mantle which we offer is best suited for round bottom flask. Proper electric wiring makes certain that no short circuit takes place. The high temperature range of 400 degrees Celsius makes our Heating Mantles ideal for industrial use.

Features :-

• Aluminum body with epoxy powder coat finish
• Fiber glass net with long lasting nichrome heating element
• High grade glass wool insulation
• Suitable for round bottom flask
• Energy regulator with corresponding lamp indicator to control the temperature
• Temperature Range: Up to 400 degrees Celsius

• Temperature & Humidity Suitable for 25 DegreeC& 60% RH, 40 DegreeC & 75% RH, 30 DegreeC & 65% RH
• Specially designed chambers to carry out stability studies at low humidity conditions such as 25 DegreeC & 40% RH, 40 DegreeC & 25% RH NMT, 30 DegreeC & 35% RH

Orbital Shaker Incubator cum B.O.D. Incubator specification designed to controlled incubation with orbital shaking arrangement with powerful geared motor for many laboratory procedures such as tissue culture, fermentations studies, Enzyme reactions, growth studies etc. The outer chamber is made up of M.S. Sheet duly painted or powder coated & inner chamber is made of thick S.S. Sheet. The gap between walls is fitted with high grade glass wool to avoid thermal loss. The plexi glass window makes it possible to inspect the specimen without disturbing the inner temp. The incubator is illuminated with one door operated or panel operated flurescent tube. The unit has a temp. Range from 5°C to 60°C. The temperature is controlled by Dual Display Microprocessor PID Digital Temperature Indicator cum Controller with a accuracy of ±0.5°C.Air circulation fan is provided to maintain stability throughout. The speed of shaker is variable from 30RPM to 250RPM.The tray of the shaker is also made of S.S. Sheet with Lotus type clamps to hold flasks. The unit is fitted with Digital RPM meter 999min digital time.

B. O. D. Incubator (bio-chemical oxygen demand)

Designed for low temperature incubation and routine determination of bio-chemical oxygen demand (B. O. D.). This unit is composed for doubled walled chamber with a thick layer of fine glass wool to prevent loss of heat and cool. For work in lower temperature a cooling unit is provided at the lower portion of the working chamber and heating arrangement has been made in the inner chamber for work of higher temperature. The temperature varies from 5º c to 60º c adjustable at any desired point by dual display microprocessor PID digital temperature indicator cum controller with a accuracy of ± 0. 5º c. Air circulating fan has been provided to keep the temperature uniform inside the chamber. Inner chamber is made up of richly anodized aluminum or highly polished stainless steel sheet. Supplied with two/three removable perforated shelves. Exterior made out of thick mild steel sheet duly finished in powder coating. Outer double wall door is provided with magnetic gasket and lock & key arrangement. Inner door made out of clear acrylic sheet allowing inspection of material in the chamber without disturbing the chamber temperature. Door operated inner illumination has been provided. Refrigeration unit is formed by ISO/ ISI marked compressor. Control panel is provided with toggle switch, temperature controller, various indicators etc. Complete with automatic internal light, l- shaped thermometer, connecting cord and plug to work on 220v ac 50 hz single phase.

chamber size in mm cap. (cu. Ft) cap. (aprox. )
455x410x610 4 112 Ltr.
505x415x830 6 171 Ltr.
565x565x865 10 280 Ltr.
650x580x900 12 336 Ltr.
700x650x900 15 420 Ltr.

Optional extra cost :-

• Timer 0 – 24 hours.
• Internal illumination with 3 florescent tubes.

• Micro processor controlled, Micro-Centrifuge machine (Mini Centrifuge)
• Speed range from 1000 to 10000 r.p.m. in step of 1000.

• Fitted with maintenance free motor (Brushless without carbon) Complete body made of ABS plastic injection moulded.
• Fitted with 0-15 minute digital timer.
• Supply completed with 2 standard rotors as under :

• Micro-Centrifuge machine (Mini Centrifuge)

• Speed fixed 7000 rpm

• Fitted with high quality motor with carbon brushes.

• Complete body made of ABS plastic injection moulded.

• Supply completed with 2 standard rotors as under :

Double walled, inner made of Stainless Steel, outer made of thick best quality Mild Steel, the surface of which is powder coated. Insulation between inner and outer wall is done with glass wool to prevent any heal loss. Inner chamber is provided with 3 nos. perforated Stainless Steel shelves with ribs to adjust the shelves at desirable height.Provided with double door, inner made of thick transparent full view glass and outer door is double walled metallic properly insulated with glass wool and also provided with best quality handle, gasket etc. Whole unit is mounted on castor wheels.Temperature range is from ambient to 60°C and is controlled by Dual Display Microprocessor PID Digital Temperature Indicator cum Controller.Heating is done with ISI mark strip type healers placed around the inner chamber. Air circulation fan is provided to maintain stability throughout Humidity will be maintained up to 95% with an accuracy of ±3% and humidity is generated by a stainless steel tank and is controlled with the help of Imported Humidistat and is indicated by Round Hygrometer. Provided with On/Off switch. Indicators. Digital Controllers etc.

Refrigerated Universal Centrifuge Machine 16000 r.p.m have Speed of 16000 rpm . Further, speed depends upon rotor being used. Fitted with microprocessor based LCD panel for 0-59 minute’s countdown timer, digital rpm meter and programmable speed controller . Stand by temperature from -20°C to room temperature is controlled by microprocessor based digital temperature controller cum indicator. Working temperature from -8°C.

1. Double walled unit mounted on a sturdy angle iron frame. 

2. Inner and outer made up of heavy M.S. Sheet. 

3. Outer body is hammertone painted.

4. Supplied with Aluminum trays as per tray capacity of the unit. 

5. Inner body is painted with high temperature aluminum paint.

6. Gap between two walls is filled with high-grade glass wool to minimize thermal loss.

7. Brackets to support the heavily laden drying trays at adjustable height are provided on the sides of inner walls.

8. Heating is brought about by strip type air heaters.

9. Temperature range from ambient to 150^oC.

10. Temperature is controlled by Microprocessor Based PID Digital Temp. Indicator-cum-Controller with an accuracy of + 1^oC.

11. Ventilation is provided with adjustable opening at the top to exhaust the fumes or vapours produced during processing.

12. Heavy duty 'V' belt driven motor of suitable capacity provides forced air circulation so as to ensure uniform heating throughout the inner chamber.

13. A separate control panel is fitted to the chamber with individual control for ON / OFF and air circulating fan.

14.To work on 220 Volts or 400/440 Volts A.C. supply only.

OPTIONAL ACCESSORIES

A. Additional Standard Tray of size 800 x 400 x 30 mm, if required.

B. AUTO TIME CONTROL UNIT : Specially designed MICROPROCESSOR BASED PID DIGITIAL TEMPERATURE INDICATOR-cum-controller with an in-built DIGITAL TIMER to control the temperature from 50^oC to 150^oC (+1^oC). Once the unit is switched heating starts automatically and once the set/desired value is achieved the In-built AUTOMATIC DIGITAL MINUTE TIMER starts automatically. Once this set time period is over the heaters are switched "OFF" automatically and the unit sounds a BUZZER, thus alerting the user that process is complete. To cost extra, in lieu of MICROPROCESSOR based PID Digital Temperature Controller.

These units are double walled with inner chamber made up of S.S sheet and outside of M.S. duly powder coated. The gap between the walls is fitted with special grade glass wool in order to avoid thermal losses. The inner chamber fitted with immersion type heating element is covered with perforated removable diffuser tray. The cover is provided with the unit as a standard accessory. Temperature from ambient to 100°C is controlled by hydraulic capillary type thermostat with accuracy of ±1°C. Workable on 220 AC 50Hz single phase.

Chamber size in mms Suitable racks Cap(Approx.)
300x175x175 1 rack 12L
300x250x175 2 racks 14L
375x300x175 4 racks 18L
455x300x175 6 racks 25L
605x300x175 8 racks 32L

Optional (extra cost):

• Microprocessor PID digital temp. indicator cum controller.
• Stirrer with 1/20 Hp motor with S.S. rod & blade.
• Autocut off device when waterlevel is low.

Haematocrite Centrifuge 13000 r.p.m. Microprocessor based, Digital Timer, r.p.m meter and programmable speed regulator.
Supply completed with Rotor +Reading Device + 1 Pkt. Capillaries, 1 Pc. Wax sealing Tray and instruction manual.

•  5 step speed controller
•  Supplied with metal carriers
•  Autoclaveable tubes with swing rotor head of 15ml
• Specifications:
•  Maximum Speed: 3500 RPM, Max RCF (xg) 1600
•  Width: 330
•  Depth: 330
•  Height: 295
•  To work on 220/240 volts 50 Hz A.C. Supply

optional extra cost :-

a. timer 0 – 24 hours.
b. internal illumination with 3 florescent tubes.

With accuracy 2%, Built in Amici prism and special light reflection system for colour elimination to obtain sharp critical boundary line and optimum contrast.

Specifications:

Single Body Mortuary Showcase

Features:

• Low Maintenance with Facility for preservation of dead body for longer periods
• Mortuary is made up of stainless steel 304
• Dead Body can be Viewed from all angles
• Digital Display PID controller
• Mortuary showcase is mounted on wheel
• Temperature range from   ( - 2^° to 8° C )
• Mortuary has top door opening dome type made up of transparent or crystal clear material non breakable

 ( Fiber glass with side view acrylic)

We are a highly acclaimed company for offering Double Oblique Bore Stopcock to clients. This product is admired for their lightweight and dimensional accuracy. Double Oblique Bore Stopcock is extensively recommended by various numbers of clients. Offered range is made by using best quality raw material and high technology machine under the guidance of the professionals. This product can be obtained by our clients at market leading price.

Features:

• Resistant to chemicals
• Light weight
• Accurate dimensions

Tuning fork Steel

Owing to our expertise in this field, we manufacture and supply a broad range of Steel Tuning Fork that is fabricated using supreme grade raw materials that are sourced from the certified vendors of the market. The steel tuning fork is designed as per the industry standards using latest techniques. This Steel Tuning Fork is tested on defined parameters to ensure its reliable performance, high tensile strength, longer service life & durability.

Steel tunning fork- Set Of 8 Forks.They have following frequency-
256-C
288-D
320-E
341.3-F
384-G
426.6-A
480-B
512-C

Tuning Fork (Harmonic)

Backed with a team of dexterous professionals, we manufacture and supply a wide gamut of Harmonic Tuning Fork that rejuvenates the body by a process of cellular memory based on the natural ratios of the tuning forks. This harmonic tuning fork is fabricated using premium quality raw materials as per the set industry standards and is tested on defined parameters in order to ensure accurate dimensions and perfect finish. The Harmonic Tuning Fork comprises a set of eight tuners and is well-known for flawless functionality, easy operation and a longer service life.

Benefits:

· Fast, instantaneous relaxation

· Altered state of consciousness

· Re-proportions your body

· Physical/psychic re patterning of your mind, body and spirit

· Develop and refine your sonic abilities

This set contains a full octave of tuning forks (C, D, E, F, G, A, B, C). When played together they create a series of overtones to help you relax and center yourself. Each interval relates to a different state of consciousness and body posture. Each interval affects your nervous system in a different way by activating specific elemental qualities.

The Solar Harmonic Spectrum is the full octave of tuning forks in a beautiful velvet pouch.

Tuning Fork (Steel Ball)

We have established ourselves amongst the renowned manufacturers and suppliers in the market with an assortment of Steel Ball Tuning Fork. The steel ball tuning fork is highly appreciated due to its reliable performance, durability, sturdy construction & immaculate finish. Designed and fabricated using unmatched quality raw materials and latest technology as per the international quality criterion, our Steel Ball Tuning Fork is also tested on defined parameters.

Tuning Fork (Aluminium Weighted)

We are counted amongst the leading manufacturers and suppliers of a wide array of Aluminum Weighted Tuning Fork like Earth Tuner and Otto 128. Fabricated using optimum quality raw materials and pioneering technology, the aluminum weighted tuning fork is used to relieve physical pain and to relax the joints, muscle & nerve groups. This Aluminum Weighted Tuning Fork is immensely used by massage therapists, acupuncturist and chiropractors due to the qualities like robust construction, light weight and corrosion resistant finish.

• _{Comes with 4 Liter /Hr output capacity}
• _{Features use of 3 kw heater load support}
• _{Works on 220/230 Volts A.C. supply}
• _{Finds application in making of pyrogen free distilled water}

• _{Steel Manufacturing Units}
• _{Ferrous and Alloy Steel Foundries}
• _{Forging Units}
• _{Wire drawing Units}
• _{Quality Control Testing laboratories}

Cabinet frame of ply-board covered with sunmica from outside. Work bench top of stainless steel. In this Bio Safety Cabinet Side and front door of work bench covered with acrylic . Motor & blower assembly to provide sufficient air pressure. HEPA filter efficiency 99.97% down to 0.3 micron. Pre-filter efficiency 99% down to 5 micron. Cock for gas. Front half opening collapsible acrylic door with gloves arrangement. Virus burnt out unit attachment. 20W flourscent tube light & 15/30W UV Germicidal Tube. Removable covers. With exhaust system.

FLOCULATOR ( SIX JAR TEST APPARATUS)has been specially designed for use in water treatment plants to correctly estimate the dosing of alum and such other coagulants for treatment of water.FLOCULATOR ( SIX JAR TEST APPARATUS)consist of electronically controlled variable speed electronic motor with timing belt driven mechanism. Speed controller is provided to control the speed of four/six stirrers from 5 to 150 RPM. Stainless Steel/ Brass paddles are provided.

Made of GI sheet 50mm diax300mm height

Mounted on a base having 2 tube inlets for thermometers, with a gallery of 60mm Ht.x150mm dia. For placing mixture of ice and salt complete with bungs and thermometers.

For injecting formaldehyde solution in cadaverous at much higher speed than normal gravity process. The body of the Embalming Machine(Cadaverous Injector) machine is made of Stainless Steel/ Mild Steel (As required). Unit is fully covered & mounted on a portable trolley having four castor wheels for easy movement. Unit consists of one air compressor which is connected with a stainless steel tank of 10 liters capacity meant for storing and injecting the solution. Incorported with latest Reciprocatory pressuring unit for efficient performance. The machine is Completely Noiseless and Vibration free which justifies the Superiority of our machine from the other brands available.Tank is fitted with a safety valve, pressure gauge and rubber tubing having provision for injection.

Supplied complete with electric cord, plug and suitable to work on 220 volts, 1ph 50 hz, ac supply.

Tuning Fork Weltch Type

Set of 8 tuning fork of nickel plated steel with plain or screwed shank in case, frequencies marked from (C1 256) to (C2 512) as above.

Tuning fork (Steel Half Ball Handle)

With the range of Steel Tuning Fork (Half Ball Handle), we have gained enormous appreciation in the market as a reputed manufacturer and supplier. This steel tuning fork is designed and manufactured using superior quality raw materials and latest machines in order to meet the international standards. The Half Ball Handle Steel Tuning Fork is highly in demand amongst our clients due to the features like sturdy construction, durable finish standards and resistance to corrosion.

Steel Tunning Fork(Half Ball Handle)-Set of 8-They Have following Frequency
256-C
288-D
320-E
341.3-F
384-G
426.6-A
480-B
512-C

Tuning Fork Set Blue Steel

Set of 8 of blue steel, plain shank, one each of c(256) d, e, f, g, a, b, c (512) in velvet lined box.

· Complete workstation containing embalming trolley and embalming machine

· Suited to equip embalming machine model em-05

· Trolley made of complete SS manufactured without rivets or bolts on the surface

· Embalming machine mounted on the underlying frame for complete system transportation

· Manual ratchet system provided for Brandenburg position

· Embalming machine can be dismounted and used separately

· Provided with heavy castor's for easy movement with or without embalming machine

· Embalming trolley approx 60" length x 28" width x 34" height

· Embalming machine uses specialized noiseless pump for suction and delivery at preset optimum pressure

· Fluid delivery rate 10ltrs/hr

· Complete SS outer body mounted on castor's

· SS inner tank with fluid capacity provided

· Complete SS outer body mounted provided

· Approx size of the em -05, 24" length x 19" width x 14.5"height

Cadavar tank more often used for cadavar storage in teaching facilities.

• These are sturdy double walled units outer chamber made of M.S. sheet duly enamel painted.
• Inner made up of mild steel or S.S sheet (AS ORDERED).
• Inner chamber is provided with ribs for adjustable perforating shelves to convenient height.
• Temperature is controlled by Microprocessor Based PID Digital Temperature cum Indicator from ambient 300 C or 390 with accuracy ± 5c.
• Air ventillator are also provided on the side or back of the unit.
• To work on 220/230 volts A.C. supply.
• All Units are fitted with air circulating fan as a standard features.

Student Spirometer:

• 6 liter capacity for vital capacity
• Used as a gas meter with chain/ plastic tread compensated counter balance to the float balance to cut its movement
• Pulley calibrated to denote volume inlet & outlet tubes
• Side cock for gases
• Cock for draining off water strong construction
• Complete with corrugated tube mouth piece and recording lever

Microprocessor Hemoglobin Meter with 16×2 lines LCD display for direct HB results soft touch keys , auto calibration. Standard memory facility . 1 ml Sample measurement .

With the range of Steel Tuning Fork (Half Ball Handle), we have gained enormous appreciation in the market as a reputed manufacturer and supplier. This steel tuning fork is designed and manufactured using superior quality raw materials and latest machines in order to meet the international standards. The Half Ball Handle Steel Tuning Fork is highly in demand amongst our clients due to the features like sturdy construction, durable finish standards and resistance to corrosion.

Steel Tunning Fork(Half Ball Handle)-Set of 8-They Have following Frequency
256-C
288-D
320-E
341.3-F
384-G
426.6-A
480-B
512-C

We own a rich experience in dealing with Laboratory Haemoglobinometer. Our offered range of Laboratory Haemoglobinometer is easily and conveniently used by the number of satisfied customers. They are specifically designed according to demand of our customers. We never compromise with the product quality as develop our products using the best techniques. Our ranges of products are highly appreciated among our clients due to their trouble free performance and superior quality.

Features:

• High grade quality
• Superior in performance
• Affordable prices

Light weight with ceramic fibre wool installation in place of refractory bricks.Working temperature 1150C.Maximum temp. 1200C.Fitted with energy regulator.CI.AL thermocouple with prometer.Heeating elements are made up of kanthal wire.Workable on 220V AC 50Hz Single Plase.

Inner Size(mm) Inner Size(Inch)
225x100x100 9"x4"x4"
250x125x125 10"x5"x5"
300x125x125 12"x5"x5"
300x150x150 12"x6"x6"
300x200x200 12"x8"x8"
350x175x125 14"x7"x5"
375x175x125 19"x7"x5"
350x225x225 18"x9"x9"

Optional:-
(a) Digital Temperature indicator cum controller.
(b) PID Digital Temperature Controller.

Soxhlet Extraction Unit with Energy Regulator:

These are ideal heaters for extractors of soxhlet & other types. This apparatus is suitable for heating soxhlet flasks of 50-500 ml and consists of two vertical & one horizontal rod with adaptors, mild steel sheet housing & screws to hold the flasks. These work on 220/230 A.C.

Models:

• Unit of 3 test Mantle Type (Without Glass parts & Clamp)
• Unit of 6 test Mantle Type (Without Glass parts & Clamp)

2. Special design ensuring best hygiene reliable.  

3. Sturdy Construction.                                      

4. Digital Temperature indication.                          

5.  Low Maintenance. 

6. Light Weight. 

Construction Detail:- PHYSILAB Lab Refrigerator is double walled. Outer body of our Lab Refrigerator are constructed out of thick steel/aluminum sheets, painted with long lasting stove enamel or elegantly powder coated. The inner chamber is made of heavy gauge stainless steel sheet of 304 grades. The 100mm gap between the walls is insulated with high grade poly uretherane insulation, which ensures maximum thermal efficiency. Outer 

1. Mounted on a sturdy angle frame the inner chamber is made up of stainless steel 304 grade with 26 SGW and outer of mild steel(C.R Sheet) 20 & 22 SGW duly enamel painted.                          

2. Double walled units have thick PUF insulation between inner and outer wall.                            

3. The temperature is maintained with in 2ºC to 8ºC.Temperature is controlled by Digital Indicator-cum-Controller.                                                  

4. Unit is provided with Audio Visual Alarm which triggers in the event of fluctuation exceeding permitted tolerance.                                          

5. Besides outer double walled door, a full view inner glass door allows inspection of test samples without disturbing the inner chamber conditions.  

6. Unit is also fitted with Power Supply Failure Alarm as a safety device Three or four drawers are provided for holding laboratory material.              

7. CFC Free ECO Friendly Compressor.                  

8. Body is mounted on caster wheels to move the refrigerator anywhere in lab.                                

9. Capacity 171 Liters. Volume 6.1 Cuft.            

10. The refrigerator work on 220/230Volts AC Supply, Make ‘PHYSILAB’ with ISO Certified Co.

Working Temperature maximum 1000C. Fitted with energy regulator. CI/AL thermocouple with prometer.Heating elements are made up of Kanthal wire.Workable on 220V AC 50Hz Single Phase.
Inner Size(mm) Inner Size(Inch)
225x100x100 9"x4"x4"
250x125x125 10"x5"x5"
300x150x150 12"x6"x6"

Optional:-
(a) Digital Temperature indicator cum controller.
(b) PID Digital Temperature Controller.

Flask Flat Bottom

100ml
250ml
500ml
1000ml

As per the demands of our clients, we offer a broad collection of Steel Tuning Fork Set (Chrome Plated). The chrome plated steel tuning fork set is precision engineered using high grade raw materials in compliance with the set industry parameters under the guidance of our skilled quality controllers. Due to the features such as sturdy construction, durability and dimensional accuracy, this Chrome Plated Steel Tuning Fork Set is highly in demand in the market.

Steel Tunning Fork- Set Of 8 Forks (chrom plated)- They have the following
Frequency-
256-C
288-D
320-E
341.3-f
384-G
426.6-A
480-B
512-C

Heavy & stable cast iron base duly painted with mild steel chrome plated upright rod. Ac/dc motor with s. S. Stirring shaft and blades, variable speed controlled unit is provided. 1/20 hp motor provided for smooth longtime stirring. Height of stirrer and stirring space adjustable. To work on 220v ac 50hz single phase

Kjeldhal distillation apparatus with glass parts

Complete with mild steel tubular stand provided with one heating box, Brass condenser rack with water circulation system, brass molded condenser clamps. Heater box is provided with top to receive the KJEDHAL flasks, with electric heating element of 500 watts each regulator, without glass parts.

a)     Unit of 3 test with On/off switches. ( Heater Type)

b)     Unit of 3 test with On/off switches. ( Mantle Type)

c)     Unit of 6 test with On/off switches. ( Heater Type)

d)     Unit of 3 test with On/off switches. ( Mantle Type)

Note : Sunvic Energy Regulator can be fitted at extra cost.

We specialized in manufacturing and supplying a wide range of bunsen burner with stop cocks. These Bunsen burner with Stop Cocks are one of the best laboratory instruments offered by our organization. Devices offered by us are manufactured by dedicated and experienced technicians, having years of experience. These Bunsen Burners offered by us are also fitted with stop Cock to balance the flame of the Burner.

Features:

• Safe to use
• Available in various sizes
• Compactness 

We offer our clients a wide range of vacuum pump: "Oil Filled Double Stage" which are manufactured by implementing original technology. These vacuum pumps are widely praised for its various special features and superb performance. Light weighted these vacuum pumps are very easy to use and carry.

Features:

• Higher Vacuum: Double stage they can satisfy different demands of vacuum
• Smaller and Lighter Design: Special Preventing oil -returning design. It guarantees there is no pollution in the system being air tighter.
• Powerful starting ability.
• It works on 220 Volts × 10%, 50 Hz A.C.

Capacity:-50 Ltr.25 Micron 1/4 1/4" 180ml.

Skinfold Caliper(Dial Type) (Made in India)
The Skinfold Caliper is used for estimation of body fat by skin fold
thickness measurement .The Skinfold Caliper tester pinches the skin at the appropriate site to raise a double layer of skin and underlying adipose tissue, but not the muscle. The calipers are then applied 1cm below and at right angles to the pinch, and reading taken 2 seconds later .The measured value is given by the special dial type gauge fixed in the instrument. This Skinfold Caliper is nicely painted to give an aesthetic appeal . The instrument has a range of 80mm with a resolution of 0.01mm.

Customers can avail from us a diversified range of digital PH meter. Engineered using best available raw materials and by implementing latest technologies, these digital PH meters are hugely recommended by large number of clients. These Digital PH Meters are designed by expert engineers having years of experience. Apart from all, we also offer customized solution as per the need and specifications of our clients.

Features:

• Robust design
• Optimum quality
• Easy to install

1. made out of thick square ms pipe frame.

2. distance between shelves to shelves is 16.

3. size of each shelf is 48 x 18.

4. platform surface will be of 3mm thick.

5. four 40-watt fluorescent light (with electronic ballast).

6. minimum heating effect/heat dissipation.

7. no flickering effect.

energy saver with individual switching arrangement in each shelf.

• total 16 electronic ballast/simulator.
• 4x25 watt incandescent lamps in each shelf with switching arrangement.
• frame with ms square pipe 1 x 1 with anticorrosive, humidity resistant powder coating finish culture rack.
• wheel/castor-4no. S for each trolley.
• provision for connecting the trolley to photoperiodic timer/controller output.
• input 200-240 v ac, 50hz, single phase, ambient 5^oc to 50^oc, rh upto 95%.

No. Of shelves:

a. unit of four shelves (lighting facility in 3 shelves).

b. unit of five shelves (lighting facility in 4 shelves).

c. unit of six shelves (lighting facility in 5 shelves).

"PHYSILAB" Offering Respiration Pump:
Respiration instruments :
Ideal Respiration pump : (V.R.V.S.)
Single cylinder pump with mechanically operated value. All metal construction. The driving cone has 3 slots of 6", 9", 12" dia and is accurately balanced. A 0.25 HP motor workable on 220V AC 50Hz single phase operates with the pump. The stroke is adjustable and is graduated in CCS up to 250cc. Motor coupled on adjustable castor wheeled base.
Ideal respiration pump : (V.R.V.S.)

Note:-Same as above but capacity up to 500 CC.

Item Code HL- 2367
Centrifuge machine offered by us offer multipurpose functionality in the laboratory environment for carrying out routine/ special work in medical & industrial laboratories. This table top centrifuge is very compact and feature robust construction. Its special features include transparent see through acrylic lid for angle rotor head, easy lid lock, step less speed controller, safety fuse & attractive front panel. We supply it with detachable metal carriers with up to 4000-6000 RPM.
Other Features:

• Step less speed controller
• Digital Speed Meter (RPM)
• 60 minute digital preset Timer

Models:

• With 8x 15ml Angle Head
• With 12x15ml Angle Head
• With 16x15ml angle Head
• With 24x 15ml Angle Head